If your bathroom has a corner garden tub on a tiled platform, a cultured marble top with the sink molded in, polished brass faucets and a strip of round bulbs over a mirror glued straight to the wall, you are standing in the classic nineties builder bathroom. A great many houses built in that decade got one, and plenty still have it. The people living with it tend to want the same thing: a room that feels calm and current, without a gut job that was never fully needed.

A 1990s bathroom remodel goes best as a sequence rather than a wish list. The order matters more than the finishes, because each stage protects the one before it: check what is behind the walls before choosing tile, lock the layout before buying a vanity, finish the wet work before the paint. Done in order, a surprising amount of the original room can stay, and the money goes where it changes how the room feels to use.

The stages below run from the first walk-through to the final punch list, with the measurements and the test for “done” at each one. Start with a clear look at what you have.

Start by Naming What the Nineties Left in the Room

Large nineties builder-grade primary bathroom: angled corner garden tub platform tiled in white with a jetted tubSave

The first stage costs nothing and takes about an hour. Walk into the room with a notepad and list every original feature by name, not by feeling. “Dated” is not a feature. “Angled corner garden tub on a tiled platform” is. In a large nineties primary bathroom like this one the list usually runs to a dozen lines: the jetted tub set into a white tile platform across one corner, the chrome-framed glass shower stall beside it, two honey oak vanities on opposite walls, white cultured marble tops with the sinks molded in, large plate mirrors, chrome bars of globe bulbs, cream walls, beige square floor tile and the row of windows at the back.

Next to each line, write what it is made of and what condition it is in. Open every vanity door and look at the cabinet floor for swelling or dark rings, the sign of a slow drain leak. Fill the tub above the jets, run them, and listen for grinding or a pump that labors. Close the shower door and check whether the chrome frame still seals, or whether a black line has formed along the bottom track. Press the floor tile with your heel near the tub and the toilet; a tile that rocks, or a grout line cracked in a long straight run, can mean movement underneath. Note the ceiling height, the window sizes and which way the door swings.

Then measure. Width, length and ceiling height, the position of every drain, the distance from the toilet centerline to the nearest wall, and the clear floor in front of each fixture. Draw it on graph paper at 1/4 in to the foot, the scale most remodel drawings use. In a room with an angled tub platform, measure the platform itself, because it often takes a 5 by 5 ft (152 by 152 cm) square of floor or more, which makes it the single biggest piece of real estate in the room.

This list takes the emotion out of the project. A room like this reads at first glance as one big beige problem, and that impression pushes people toward tearing everything out. Written down, it becomes a dozen separate decisions, and several of them turn out to be easy keeps. Two separate vanities on opposite walls, for instance, are a layout many couples would happily pay to add.

Done looks like one page with every feature, its material, its condition and its measurements, plus a floor sketch with the drains marked. Nothing gets bought until that page exists.

Key Takeaway: Write down every original feature with its material, condition and measurements before you decide anything, so the remodel becomes a list of separate calls instead of one overwhelming room.

Editor Pick
Mestikits Frameless Bathroom Mirror, 30"x36" Beveled Bathroom Mirror for Vanity, Wall Mount Mirrors with 4mm Tempered Glass for Bedroom Entryway Living Room Hangs Horizontally or Vertically
Mestikits Frameless Bathroom Mirror, 30"x36" Beveled Bathroom Mirror for Vanity, Wall Mount Mirrors with 4mm Tempered Glass for Bedroom Entryway Living Room Hangs Horizontally or Vertically
Check price

Sort Each Feature Into Keep, Refresh or Replace

Chart: Keep, Refresh or Replace. Give every original feature one label. Your condition notes win over the general rule.Save

Now give every line on that page one of three labels. Keep means it stays exactly as it is. Refresh means it stays but gets a new surface, a new finish or new hardware. Replace means it comes out. The chart above sets out the usual call for the features nineties bathrooms share, but your condition notes from the first stage always win over the general rule.

Most of the keeps are structural. A honey oak double vanity with raised panels, doors that close true and a dry cabinet floor is worth keeping or refreshing; cabinet boxes from that era were often built more solidly than much of what is sold flat-packed now. Remodelers who work on these houses say the same of the room as a whole: the layouts often work and the plumbing rough-ins are usually fine, which is exactly why moving fixtures is where budgets break. A drop-in soaker in good condition can stay as it is or be reglazed. A wide window, generous floor space and a separate tub and shower are features buyers still look for.

The refreshes are the surfaces you see and touch. Oak can be refinished in a matte clear coat or painted. Cultured marble with a stained deck but a sound bowl can be professionally refinished. Sage green walls can stay sage or become another color in an afternoon. An oak-framed mirror can be painted or simply kept, once the lights beside it change. Tired grout can be cleaned, stained or raked out and redone.

The replaces are usually the parts that fail or wear out. Polished brass faucets whose clear coat has peeled will not come back, and metal finishers will tell you that replating a single faucet often costs more than a new one. Chrome bars of globe bulbs throw hard light down the face and glare in the mirror. A sheer lace curtain in a room full of steam holds mildew. Carpet anywhere near a tub or toilet goes, every time.

Two rules keep the sorting honest. First, anything that leaks, flexes or smells is a replace, however good it looks. Second, the more items you can honestly mark keep or refresh, the more of the budget is left for the two or three changes that matter most to how the room feels, which are usually the tub, the light and the floor.

Done looks like every feature labeled, with a one-line reason beside each label. Circle the replaces. That short circled list is the real scope of your remodel, and it is almost always shorter than the list you imagined on the first day.

Key Takeaway: Label every feature keep, refresh or replace, treat anything that leaks or flexes as a replace, and let the circled replaces define the scope.

Editor Pick
Ravinte Brushed Brass Solid Knobs Gold Kitchen Cabinet Pull,30 Pack,Round-5 | Zinc Dresser Handles, Gold Cupboard Hardware, Door Drawer Knobs, screws & screwdriver included, For Cupboards, Dressers
Ravinte Brushed Brass Solid Knobs Gold Kitchen Cabinet Pull,30 Pack,Round-5 | Zinc Dresser Handles, Gold Cupboard Hardware, Door Drawer Knobs, screws & screwdriver included, For Cupboards, Dressers
Check price

Check Behind the Surfaces Before You Pick a Single Finish

Authentic nineties builder-grade full bathroomSave

Before you fall for any tile, find out what the existing room is hiding. The expensive part of a nineties bathroom is rarely the color of the tub. It is the slow leak behind the tile apron, the soft subfloor beside the toilet and the exhaust fan that has been pushing wet air into the attic for decades. Remodelers who specialize in these rooms put it plainly: the real costs sit behind the surface, and finding them before the design is set is what keeps a budget intact.

Start with the wet zones. A seafoam whirlpool tub dropped into a white tile platform, like this one, has two weak points. One is the grout and caulk along the rim, where water sits every time the tub is filled. The other is the pump bay, usually reached through an access panel in the platform. Shine a flashlight along the rim joint. Gaps, black lines or caulk that lifts away in strips mean water has had a way in. If you can open the pump panel, look at the framing and the subfloor below the tub for stains or soft spots. Run the jets for ten minutes and check the panel again afterward.

Then check the floor. Small square ceramic tile, the kind that covers this floor and the tub platform, shows movement as grout lines cracked in straight paths. Stand beside the toilet and shift your weight. Any give, or a toilet that rocks, means the wax ring, the flange or the subfloor needs attention. From the room below, look at the ceiling under the bathroom for old water rings.

Behind shower walls, builders of the period often used moisture-resistant drywall, the green-faced board, as the tile backer. It resists moisture for a while, but it is not waterproof, and once it has been soaked a few times it softens. Press firmly on the tile around the shower valve and in the lower corners. Tile that moves or sounds hollow across a wide area usually means the backer has failed, and that wall comes out regardless of how you feel about the tile.

Finally, go into the attic, or take down the fan grille, and follow the fan duct. It should end at a roof or wall cap outside. A duct that stops in the insulation, or no duct at all, is a common find in these houses, and it explains the peeling ceiling paint.

Done means each check has an answer written beside it: rim joints, pump bay, floor, toilet, shower walls, fan duct. Anything wet or soft moves straight to the replace list, and it gets fixed first.

Key Takeaway: Inspect the tub rim, pump bay, floor, toilet, shower backer and fan duct before you design anything, because hidden water damage sets the scope, not the finishes.

Editor Pick
GE Advanced Silicone Caulk for Kitchen & Bathroom, White, 2.8 fl oz Tube, 1 Pack - 100% Waterproof Silicone Sealant, 5X Stronger Adhesion, Shrink & Crack Proof
GE Advanced Silicone Caulk for Kitchen & Bathroom, White, 2.8 fl oz Tube, 1 Pack – 100% Waterproof Silicone Sealant, 5X Stronger Adhesion, Shrink & Crack Proof
Check price

Lock the Layout and the Clearances It Has to Meet

Chart: Clearances the Layout Must Meet. Code minimum first, the more comfortable NKBA number second.Save

With the hidden problems known, settle the layout on paper before you buy anything. The rule that keeps a remodel affordable is simple: leave the toilet, the sinks and the tub drain where they are unless there is a strong reason to move them. Each move drags a drain, a vent and a supply line with it. On a concrete slab a moved drain means cutting and patching the floor; on wood joists it is easier, but it is still one of the largest lines on most quotes.

Before you lock the plan, check that every fixture meets the clearances in the chart above. The International Residential Code, which most US towns adopt in some edition, asks for at least 15 in (38 cm) from the center of the toilet to a side wall or obstruction and 21 in (53 cm) of clear floor in front of it. The National Kitchen and Bath Association recommends more comfortable numbers: 18 in (46 cm) to the side and 30 in (76 cm) in front. In front of a shower opening, the code asks for 24 in (61 cm) of clear space. A double vanity is easiest to share when the two sink centers sit about 30 in (76 cm) or more apart.

Nineties primary bathrooms usually pass these numbers with room to spare, because they were built large. The real layout questions are about the big pieces. A corner whirlpool tub about 60 by 60 in (152 by 152 cm) holds a 3,600 square inch footprint, more than a 36 by 60 in (91 by 152 cm) shower takes. A long honey oak double vanity with a tile counter and carpet in front of it raises a second question: is there room for two sinks and a stretch of real counter between them, or would one wide sink serve the household better?

Work from the sketch you made in the first stage. Mark every clearance zone as a shaded rectangle in front of its fixture. Where two zones overlap, the room will feel tight in daily use even if it technically passes, so that is where you either shrink a fixture or move one.

Check the door as well. A door that swings into the room and hits the vanity or the toilet zone can be rehung to swing the other way, or swapped for a pocket door, which frees more floor than most people expect.

Done looks like a final floor plan with fixtures drawn at their real sizes, every clearance shaded, and a short note beside each drain saying “stays” or “moves.” That plan is what every quote should be priced from.

Key Takeaway: Keep drains where they are wherever you can, and check every fixture against the code minimums and the more comfortable NKBA numbers before you buy anything.

Editor Pick
Super Area Rugs Oval Braided Rugs for Kitchen - Cotton Braided Rug 2x3 - Oval Soft Bathroom Throw Rugs, Woven Rug for Bedside, Blue & White
Super Area Rugs Oval Braided Rugs for Kitchen – Cotton Braided Rug 2×3 – Oval Soft Bathroom Throw Rugs, Woven Rug for Bedside, Blue & White
Check price

Decide What Happens to the Garden Tub

Bright renovated primary bathroomSave

The corner garden tub is the defining piece of the nineties primary bathroom, and the biggest decision in the remodel. Remodel guides call it the most common casualty, an oversized drop-in that takes real square footage and rarely gets filled. That is true in many houses. It is not true in all of them, and the right call depends on how you actually use the room.

There are four honest options. The first is to keep the tub and change what surrounds it, which is what this bathroom did: the corner soaking tub stayed, its platform was retiled in plain white, and the room around it was rebuilt with a white double vanity, quartz, brushed nickel and a frameless glass shower. If the tub has no leaks and the shell is sound, this is by far the least disruptive path. The second is to keep the tub and have the shell reglazed, which typically lasts somewhere around five to ten years with careful cleaning, longer when the prep was done well and harsh cleaners are kept away from it.

The third option is to pull the garden tub and set a freestanding tub in its place. A freestanding oval about 60 by 30 in (152 by 76 cm) needs far less floor than a 60 by 60 in (152 by 152 cm) corner platform, and the reclaimed corner can hold a plant, a chair or simply open floor. Freestanding tubs usually need the drain moved to suit their own outlet, and a floor-mount filler needs its supply lines brought up through the floor. The fourth option is to convert the tub space into a walk-in shower. Because a tub drain sits at one end and a shower drain usually sits near the center, the drain almost always moves, and a corner stall may mean moving or adding a wall.

Before you choose, ask one plain question: how many times did anyone in the house take a bath last month? If the answer is zero and there is another tub elsewhere in the house, the conversion or the smaller freestanding tub makes sense. Agents commonly advise keeping at least one tub somewhere in a home for resale, and the primary bathroom does not have to be the one that holds it. If the jets still run and you soak every week, keep it and spend on everything else.

If the jets stay, test the pump and the hoses now, while the walls are open nearby.

Done looks like one written decision, keep, reglaze, freestanding or shower, with the drain position for that option marked on your floor plan.

Key Takeaway: Choose keep, reglaze, freestanding or walk-in shower based on how often anyone actually bathes and whether another tub exists in the house, then mark the drain it needs.

Editor Pick
Ascher Bathroom Vanity Light Fixtures, 3 Light Wall Sconces Lighting with Clear Glass Shade, Brushed Nickel Wall Lights for Mirror, Kitchen, Living Room, Gallery, E26 Base (Bulbs Not Included)
Ascher Bathroom Vanity Light Fixtures, 3 Light Wall Sconces Lighting with Clear Glass Shade, Brushed Nickel Wall Lights for Mirror, Kitchen, Living Room, Gallery, E26 Base (Bulbs Not Included)
Check price

Plan the Demolition in the Order That Protects What Stays

Chart: Take It Apart in This Order. Each step protects the keeps on your list. The tub, if it goes, goes last.Save

Demolition feels like the satisfying part, and it is also where a remodel most often goes wrong. A cracked tub you meant to keep, a vanity scratched by falling tile, a valve knocked loose behind a wall: each of these happens because things came out in the wrong order. The chart above sets out the sequence that protects every keep on your list.

Begin with the services. Shut off the water to the room at the fixture stops, or at the main if the stops are seized, which they often are in a house of this age. Turn off the bathroom circuits at the breaker and confirm with a non-contact voltage tester at every switch and fixture. Then protect what stays. A tub you are keeping gets a layer of cardboard taped into the shell and a drop cloth over it. A vanity you are refreshing gets its doors removed, labeled and carried out of the room. Lay a path of floor protection from the bathroom door to the outside so debris does not damage the rest of the house.

Next come the soft and hanging things: towel bars, the toilet paper holder, window treatments like the pleated green fan shade in this room, shower curtain rods and the shower door. Then the mirror and the light fixtures, which get their own stage next because they need care. The toilet comes out after that; stuff a rag in the open drain flange so sewer gas and dropped screws stay out of the pipe.

Wallpaper comes off before any tile or drywall work, because the walls under it will need repair and priming either way. For a stripe paper run across the walls and the ceiling, as here, score the paper with a scoring tool, spray it with a mix of hot water and fabric softener at about one to one, let it soak for fifteen minutes, and lift it with a plastic scraper. Wash off the glue residue, let the wall dry, and plan on a primer made for wallpaper adhesive before any paint.

Carpet and pad come up next, along with the tack strip, which has sharp points that face the wall. Wet-zone tile and backer come out only where your inspection found failure or where the plan calls for a new shower. The tub, if it is going, is last, because it is the heaviest and most awkward piece and everything else should be clear before it moves.

Done looks like a room stripped to exactly the scope on your list, every keep still undamaged and covered, the drains plugged and the circuits marked.

Key Takeaway: Shut off water and power, protect the keeps, then remove hanging items, mirror and lights, toilet, wallpaper, carpet and failed tile in that order, with the tub last.

Editor Pick
WP Chomp Wallpaper Scorer Remover Tool: with Hardened Steel Wheels 52014
WP Chomp Wallpaper Scorer Remover Tool: with Hardened Steel Wheels 52014
Check price

Take Down the Plate Mirror and the Bulb Strip Safely

Long primary bathroom in nineties builder-grade condition: wide honey-oak vanity spanning the full wall with an integratSave

The full-width frameless mirror and the chrome globe bar above it are two of the most recognizable pieces of a nineties bathroom, and they are the two most likely to injure someone on the way out. A sheet of mirror the width of a long vanity, about 60 by 30 in (152 by 76 cm) here, is heavy, sharp and often glued directly to the drywall. Treat its removal as its own job.

First, find out how it is held. Look along the bottom edge: a mirror resting in a metal J-channel with clips at the top can simply be lifted out once the clips are loosened. If there are no clips, or if the mirror does not move when you press gently near an edge, it is glued with mirror mastic, and the approach changes. Before you touch it, cover the whole face in overlapping strips of clear packing tape, so that if it cracks the pieces stay together. Put on long sleeves, heavy work gloves and wrap-around eye protection, and lay a heavy drop cloth over the counter and the floor.

For a glued mirror there are two safe methods. One is to slide a length of cutting wire behind the top corner and work it back and forth through the adhesive, with at least two helpers holding the glass so it cannot fall forward as it releases. The other, which some remodelers consider safer, is to cut out the section of drywall the mirror is bonded to and remove mirror and drywall together; if that wall is being patched or replaced anyway, this is the cleaner choice. Do not try to soften the mastic with heat. Construction adhesive tends to crack the glass from thermal shock long before it lets go.

The bulb strip comes next, with the breaker off and the circuit confirmed dead. Remove the bulbs, unscrew the base plate, and look at what is behind it. You should find a proper electrical box. Some homeowners find only a hole in the drywall with wires coming through, and that has to be corrected with an approved box before any new fixture goes up. Note where the box sits relative to the center of the vanity, because your new light, or the pair of sconces you may want instead, will be planned around it.

Expect the wall behind the mirror to need work: torn paper facing, dabs of adhesive, sometimes a whole section of new drywall.

Done looks like the mirror out in one piece or safely bagged, the strip removed, the box exposed and its position measured, and the wall marked for repair.

Key Takeaway: Tape the mirror face, gear up, and remove a glued mirror with wire and helpers or by cutting out its drywall, never with heat, then expose and measure the light box.

Editor Pick
Schwer 12 Pairs A4/A5/A6 Cut Resistant Gloves, Non PFAS CR3088, L | Non Fiberglass, PU Coating, Strong Grip, Abrasion Resistant, for Glass Cutting, Warehouse Handling, Gardening Work
Schwer 12 Pairs A4/A5/A6 Cut Resistant Gloves, Non PFAS CR3088, L | Non Fiberglass, PU Coating, Strong Grip, Abrasion Resistant, for Glass Cutting, Warehouse Handling, Gardening Work
Check price

Size the Exhaust Fan and Send It Outside

Chart: Size the Exhaust Fan. Every new finish lasts longer in a room that dries out after each shower.Save

With the room opened up, deal with the air before anything new goes on the walls. A bathroom with gold bypass shower doors and a fluorescent fixture in the ceiling, like this one, very often has a small, loud fan that moves too little air, or a fan that was never ducted outside at all. Every finish you are about to buy, from the paint to the grout, lasts longer in a room that dries out after each shower.

Start with the size, set out in the chart above. The common rule is 1 CFM (cubic foot per minute) of fan capacity for each square foot of floor, with a floor of 50 CFM for even the smallest bathroom, which is also the figure the residential code uses for a fan that runs intermittently. That rule assumes a ceiling of about 8 ft (2.4 m), so add capacity for taller ceilings: roughly 10 to 20 percent more for a 10 or 12 ft ceiling. Bathrooms larger than 100 sq ft (about 9.3 sq m), which many nineties primary bathrooms are, are better sized by fixture: about 50 CFM each for the toilet, the shower and the tub, and 100 CFM for a jetted tub. A large primary bathroom with a separate shower, a jetted tub and a toilet can need 200 CFM or more.

Placement matters as much as size. Put the fan between the shower and the toilet, close to the shower but not directly above where someone stands, unless the fan is rated for that location over a tub or shower. Run the duct the shortest, straightest path to a roof or wall cap, using rigid or semi-rigid duct of the diameter the fan specifies. In a cold attic, insulate the duct so moisture does not condense inside it and run back down into the fan.

Then decide how it is controlled. A timer switch or a humidity-sensing fan solves the most common problem, which is that people switch the fan off the moment they leave. Twenty minutes after a shower is the common recommendation. Quiet matters too: a fan that is pleasant to hear is a fan that gets used, so check the sound rating on the box and favor the lowest number you can find at your size.

Done looks like a fan sized to the room, ducted to a cap outside, controlled by a timer or humidity sensor, and wired before the ceiling is patched and painted.

Key Takeaway: Size the fan at 1 CFM per square foot with a 50 CFM minimum, or by fixture above 100 sq ft, duct it to the outside, and put it on a timer or humidity control.

Editor Pick
AUPU Bathroom Exhaust Fan with Humidity Sensor,HVI&Energy Star Fan,50-80-110 CFM Household Extractor Fan,Time Delay Function,Ventilation Fan with Retractable Bracket,4''Duct,Ceiling Mounted
AUPU Bathroom Exhaust Fan with Humidity Sensor,HVI&Energy Star Fan,50-80-110 CFM Household Extractor Fan,Time Delay Function,Ventilation Fan with Retractable Bracket,4''Duct,Ceiling Mounted
Check price

Build the Shower You Will Actually Use Every Day

Traditional primary bathroom shower alcove framed by a white fluted column and crisp crown moldingSave

In most nineties primary bathrooms the shower was the afterthought: a small chrome-framed stall squeezed beside the big tub. In the remodel it usually becomes the fixture used most, so it deserves the most planning. This is the stage where you fix its size, its entry, its glass and its valve positions, all before any waterproofing starts.

Start with the size. The residential code sets a minimum of 30 by 30 in (76 by 76 cm) inside a shower, and a nineties stall often sat close to that. A comfortable walk-in for one person starts around 36 by 48 in (91 by 122 cm), and if you are converting a tub space, 36 by 60 in (91 by 152 cm) is the classic footprint, because it reuses the same wall length. A walk-in with only a partial glass panel, like the travertine shower here, needs more length, so the water has room to fall before it reaches the open end: plan on at least 48 in (122 cm), better 60 in (152 cm), with the shower head on the wall farthest from the opening.

Next, the valve and the heads. A rain head hung from the ceiling needs its supply run in the ceiling, and multi-jet body sprays need a valve and supply sized to feed them at the same time, so both are decided now, while the walls are open. Mount the main valve where you can reach it from outside the spray, often on the wall nearest the opening. A handheld on a slide bar is worth adding in almost every case: it rinses the walls and the bench and makes the shower easier to use at any age.

Then the details that make it feel finished. A recessed niche fits between two studs, roughly 14 1/2 in (37 cm) wide, and should land on an interior wall rather than an exterior one, where it would cut into the insulation. An accent border, like the blue-gray diamond mosaic running at eye level here, should be set at a height that lines up with something, the top of the niche or a full tile course, so it reads as planned. A bench or a ledge 17 to 19 in (43 to 48 cm) high is the easiest luxury to add.

Lastly the entry. A curbless entry needs the floor recessed during framing; a low curb is simpler and works well in most remodels.

Done looks like a drawing of the shower with its inside dimensions, valve and head heights, niche location, bench, border line and glass layout, ready for the waterproofing stage.

Key Takeaway: Size the shower generously, at least 48 in long for a partial glass panel, and fix valve, head, niche, bench and border positions before any waterproofing begins.

Editor Pick
NearMoon Rain Shower Head, High Flow Stainless Steel Square Rainfall Shower, Waterfall Bath Shower Body Covering, Ceiling or Wall Mount (12 Inch, Matte Black)
NearMoon Rain Shower Head, High Flow Stainless Steel Square Rainfall Shower, Waterfall Bath Shower Body Covering, Ceiling or Wall Mount (12 Inch, Matte Black)
Check price

Waterproof the Shower in the Right Order

Chart: Waterproof the Shower in Order. Green-faced drywall resists splashes, not daily soaking. Build a sealed system.Save

The tile is what you see; the waterproofing is what decides whether you are doing this job again in ten years. The failure behind many nineties showers was not the tile but the moisture-resistant drywall behind it, which tolerates splashes but not years of daily soaking. A new shower is built as a sealed system, and the order in the chart above is what makes it sealed.

Begin with the framing. Walls must be plumb and flat, and the studs sound; sister or replace any that were softened by the old leak. Add blocking for the grab bar, the glass panel’s hardware, the bench and anything else that will be screwed into the wall later. Blocking is easy now and close to impossible after tile.

Then the floor. A tiled shower floor needs a slope of 1/4 in per foot (about 2 cm per meter) toward the drain. In a traditional build that slope is created twice: once under the waterproof liner, so water that gets through the grout drains away, and again in the mortar bed on top. Many remodelers now use a foam or prefabricated sloped tray with a bonded membrane, which builds the slope and the waterproofing in one system. Whichever method you use, follow one manufacturer’s system from drain to wall, and do not mix parts.

The walls come next. Cement backer board or a foam board made for showers replaces the old drywall. Seams get mesh tape set in thin-set, and the waterproofing goes on as a liquid membrane rolled to the thickness the label specifies, or as a sheet membrane. Sources differ on whether a vapor barrier goes behind the board or a membrane goes on its face; what they agree on is that you pick one approach and never both, which can trap moisture between them. The membrane runs continuously from the floor up the walls, at least 2 in (5 cm) above the top of the curb and, in practice, to the full height of the tile in the spray zone.

Before a single tile goes on, flood-test the floor. Plug the drain, fill the pan with water to just below the curb, mark the level, and leave it overnight. If the level has not dropped and the room below is dry, the shower is sealed.

Only then comes tile, grout, and flexible caulk in every change of plane, where walls meet the floor and each other, instead of grout.

Done looks like a passed flood test, photographed, with the membrane visible before tile covers it.

Key Takeaway: Build the shower as one sealed system, framing, sloped floor, backer, membrane and an overnight flood test, before any tile goes on.

Editor Pick
Waterproof Membrane for Shower 3.8 ft x 87 ft / 324 Square Feet Waterproofing Shower Membrane 19.7mil Thickness Waterproof for Sauna Bathroom Walls Tile Underlayment 324 sqft Polyethylene Fabric Roll
Waterproof Membrane for Shower 3.8 ft x 87 ft / 324 Square Feet Waterproofing Shower Membrane 19.7mil Thickness Waterproof for Sauna Bathroom Walls Tile Underlayment 324 sqft Polyethylene Fabric Roll
Check price

Lay a Floor That Grips, Cleans and Warms the Room

Small bathroom with a white alcove tub and an L-shaped brass curtain rodSave

Once the wet walls are sealed, the floor goes down, and it is the surface that changes the feel of a nineties bathroom fastest. Out goes the beige square tile, the diamond-set ceramic or, worst of all, the carpet. In comes a floor chosen for three things: grip when wet, ease of cleaning, and warmth underfoot.

Grip comes mostly from grout lines. Small tiles, like the terracotta-colored hex mosaic in this bathroom, put a grout joint every 2 in (5 cm) or so, and those joints give bare wet feet something to hold. That is why mosaics have always been the classic shower and bathroom floor. A matte or textured porcelain helps as well; ask for a tile rated for wet floors rather than choosing by look alone. Porcelain is the practical choice for almost every bathroom floor: dense, low-absorbing and available in looks from terracotta to stone to wood.

Cleaning comes down to grout and sealing. Cement grout in a small mosaic floor should be sealed after it cures and resealed periodically; a high-performance or epoxy grout costs more and is harder to install but resists staining from the start. Choose a grout color a shade darker than the tile on a busy floor, so it does not show every footprint.

Warmth is where a remodel can quietly add real comfort. An electric radiant mat sits under the tile in a thin layer of thin-set, warming the floor through the tile. It needs its own thermostat and a GFCI-protected circuit, and it must be laid and tested before the tile goes down, so plan it now or skip it. Keep it out from under the toilet and the vanity, where it does nothing useful.

Get the levels right at the door. New tile over a new underlayment is often taller than the old floor, so plan a transition strip that does not create a trip edge, and check the door bottom clears the new height. Finish the edges with a tile base or a painted wood baseboard sealed at the bottom with caulk.

This bathroom shows how much a floor carries a room. The terracotta hex, olive wainscoting, cream walls and a medium walnut vanity all sit in the same warm earth range, and the floor is what ties them together.

Done looks like the floor tiled, grouted, sealed and cured, the heat mat tested if you used one, and the threshold finished.

Key Takeaway: Choose a porcelain floor that grips when wet, seal the grout, add an electric heat mat only if it goes in before tile, and finish the threshold so nothing catches a toe.

Editor Pick
Naturoom Linen Shower Curtain 72 Inch Long for Bathroom Beige 1 Panel | 6FT, Neutral Rustic Boho Farmhouse, Water Repellent, Bath Decor Shower Curtains, Textured Fabric with Hooks, 72x72
Naturoom Linen Shower Curtain 72 Inch Long for Bathroom Beige 1 Panel | 6FT, Neutral Rustic Boho Farmhouse, Water Repellent, Bath Decor Shower Curtains, Textured Fabric with Hooks, 72×72
Check price

Match the Floor Tile Size to the Room and the Grout

Chart: Floor Tile Size and Grout Width. Tile size sets the grout lines, the flatness the floor needs and how the room reads.Save

Tile size is not only a style choice. It decides how many grout lines the floor carries, how flat the subfloor has to be, how the pattern meets the walls and how the room reads in size. The chart above sets out the common sizes and what each one asks of the installation.

Small mosaics, roughly 1 to 2 in (2.5 to 5 cm), come on mesh sheets and follow small slopes and curves easily, which makes them the first choice for a shower floor and a good choice for any floor that gets wet. Their joints are narrow, often around 1/16 to 1/8 in (1.5 to 3 mm), but there are many of them, so the grout choice matters more than the tile. Hex and penny patterns give a bathroom an older, settled feel that suits a nineties house being pulled toward something more classic.

Mid-size tiles, around 8 by 8 in (20 by 20 cm) to 12 by 12 in (30 by 30 cm), cover most bathroom floors. Patterned tiles like the black-and-white diamond encaustic-look floor in this Victorian-style room sit here: bold enough to carry the room, small enough to lay out cleanly in a small space. Plan the layout from the center of the room, or from the most visible edge, the doorway, so the cut tiles land under the vanity and behind the toilet, where nobody sees them.

Large-format tiles, 12 by 24 in (30 by 61 cm) and up, mean fewer grout lines and a calmer floor. They also demand a flatter subfloor, because a long tile magnifies every dip, and they bring a specific rule: when laying a rectangular tile in an offset pattern, keep the offset to no more than a third of the tile length. A half offset on a long tile exaggerates the slight bow most long tiles have and leaves edges standing proud of each other.

Match grout width to the tile. Rectified tiles, cut to precise edges, can take joints around 1/16 to 1/8 in (1.5 to 3 mm). Tiles with softer, pressed edges need a wider joint, often 3/16 in (5 mm), to absorb their small size differences.

Think about scale as well. In a small bathroom like this one a busy floor works when the walls are quiet, a single pale blue, a marble top, a walnut vanity. In a large nineties primary bathroom, a large-format floor with minimal joints keeps the room from feeling like a grid.

Done looks like a tile size and grout width chosen, a layout drawn from the doorway with the cuts hidden, and the subfloor checked flat enough for the size you picked.

Key Takeaway: Pick mosaics for wet floors and showers, mid-size patterns for small rooms, large formats for calm big rooms, and keep any long-tile offset to a third.

Editor Pick
Tenedos Matte White Hexagon Porcelain Mosaic Tile with Black Flower Pattern – Bathroom Floor, Kitchen Backsplash, Accent Wall, Entryway (10 Sheets)
Tenedos Matte White Hexagon Porcelain Mosaic Tile with Black Flower Pattern – Bathroom Floor, Kitchen Backsplash, Accent Wall, Entryway (10 Sheets)
Check price

Decide Whether the Cultured Marble Top Stays

Small vintage bathroom from the doorwaySave

Cultured marble is the material most people assume has to go, and it is not always true. It is a cast blend of crushed stone and resin with a clear gel coat on top, usually molded as one piece with the sink. The nineties version was often swirled with beige or gold veining, and that swirl is what dates it. A plain white top, like the one on the espresso vanity in this bathroom, can look quiet and current once the room around it changes.

So judge it in two parts: the deck and the bowl. The deck is the flat counter. Light scratches that have not gone through the gel coat can be polished out with a mild polishing compound. Dullness and staining across the deck are what professional refinishing handles well; refinishers clean, repair chips, and spray a new coat, and they claim the finish lasts many years, though those figures come from the companies themselves. The bowl is where cultured marble usually fails. Fine cracks radiating from the drain, called crazing, come from thermal shock, the repeated swing between hot and cold water. Standing water, toothpaste and scrubbing all land in the same few square inches. A crazed bowl may hold for a while, but it rarely refinishes as well as the deck.

The rule that follows is simple. Stained or dull deck with a sound bowl: refinish, or simply polish and keep. Crazed, cracked or chipped bowl: replace. When you replace, a new integrated cultured marble or solid-surface top in a standard width is one of the least expensive tops you can buy, so check standard sizes against your vanity before assuming you need custom stone. Before deciding either way, empty the cabinet under the sink and look at its floor. A swollen or stained base means the old top or its drain has been leaking, and the cabinet repair belongs in the plan too.

You've saved it, wanted it. Here's the how: codes, measurements, order. Your choices make it yours.

See all guides →

If you keep the top, the room has to do the updating. This bathroom shows how: dark espresso wood under the white top, a brass mirror, frosted bell sconces, a dusty-rose floral paper and a checkered floor make the white surface read as a classic choice rather than a builder leftover. A new faucet in a current finish matters most, because it sits right on the top and draws the eye.

Done looks like the deck and the bowl each judged, the cabinet floor checked, and a written call: polish, refinish or replace.

Key Takeaway: Keep or refinish a cultured marble top when the deck is only stained and the bowl is sound, and replace it when the bowl around the drain has crazed or cracked.

Editor Pick
Gold Sconce Wall Lighting, HWH Indoor Bathroom Sconces with Frosted White Bell-Shaped Glass, Up and Down Vanity Lights Fixtures for Bathroom, Gold Finish, 5HZG106B-2W BG-ML
Gold Sconce Wall Lighting, HWH Indoor Bathroom Sconces with Frosted White Bell-Shaped Glass, Up and Down Vanity Lights Fixtures for Bathroom, Gold Finish, 5HZG106B-2W BG-ML
Check price

Paint the Honey Oak Vanity So the Finish Holds

Chart: Paint an Oak Vanity in This Order. A bathroom is the hardest room in the house for a painted finish. Preparation holds it.Save

A honey oak raised-panel vanity that passed your inspection has two good futures. It can keep its wood, refinished in a modern matte clear coat that takes the orange cast out of the old glossy finish; warm wood vanities are back in the latest trend reports. Or it can be painted. Painting a bathroom vanity is a project most people can do well, but only if they respect the order in the chart above, because a bathroom is the hardest place in the house for a painted finish.

Start by taking it apart. Remove the doors and drawer fronts, take off the hinges and the hardware, and label every piece with painter’s tape on the back so each door returns to its own opening. Work on the doors flat on a table, which gives a smoother finish than painting them hanging.

Then clean, because oak vanities carry years of hairspray, lotion and soap film that paint will not stick to. Scrub every surface with a degreasing cleaner, rinse with clean water and let it dry fully. Scuff-sand with 180 to 220 grit paper; you are dulling the old finish for grip, not taking it back to bare wood. Vacuum and wipe off the dust.

Oak has deep open grain, and it shows through paint unless you deal with it. If you want a smooth painted look, fill the grain with a grain filler or a high-build primer, sand it back, and repeat on the doors where it shows most. If you like a little texture, skip this step; the grain will read faintly under the paint.

Prime with a bonding primer made for glossy or difficult surfaces, which is what makes paint hold on an old factory finish. Sand lightly with fine grit once it dries. Then apply two thin coats of a cabinet enamel, a waterborne alkyd or a urethane-modified acrylic, letting each dry fully. Thin coats level better and cure harder than one thick one.

Give it time. Most cabinet enamels feel dry in hours but take two to four weeks to cure fully. Rehang the doors after a few days and treat them gently until then: no wet towels draped over them, no scrubbing.

Finish with new hardware sized to the doors, and the vanity reads as a deliberate piece of furniture rather than a builder’s stock cabinet.

Done looks like a vanity primed, painted in two thin coats, rehung, and left to cure before heavy use.

Key Takeaway: Degrease, scuff-sand, fill the grain if you want it smooth, prime with a bonding primer, and lay two thin coats of cabinet enamel, then let it cure before daily use.

Editor Pick
Rust-Oleum Cabinet Transformations & Trim Paint, Pure White, Quart | Cabinet paint, Smooth durable finish, Easy-clean coating, Quick dry formula, For cabinets and trim
Rust-Oleum Cabinet Transformations & Trim Paint, Pure White, Quart | Cabinet paint, Smooth durable finish, Easy-clean coating, Quick dry formula, For cabinets and trim
Check price

Choose a New Vanity at the Right Height and Width

Compact bathroom remodelSave

If the old vanity failed inspection, or never suited the room, this is the stage to choose its replacement, and the first number to check is height. Many vanities installed in the nineties stood around 30 to 32 in (76 to 81 cm) tall, a height that has most adults stooping at the sink. Most vanities sold now are made at what is often called comfort height, about 34 to 36 in (86 to 91 cm), close to kitchen counter height. For a primary bathroom used by adults, the taller height is almost always the better choice. If you choose a vessel sink, subtract its height from the vanity height so the rim lands near 36 in (91 cm).

Depth comes next. A standard vanity runs about 21 in (53 cm) deep. In a tight bathroom, a shallower vanity around 18 in (46 cm) gives back floor in front of the toilet and the door, often the difference between a cramped room and a comfortable one. Check the clearance plan from the layout stage before you commit.

Width follows the wall and the household. A 36 in (91 cm) single vanity, like the hunter green shaker cabinet in this compact bathroom, is the size where a single sink still leaves real counter on both sides for a toothbrush cup and a soap dish. Below 30 in (76 cm), plan on storage elsewhere, such as floating shelves above the toilet like the two walnut shelves here.

Then material. Painted wood, solid wood and wood veneer over plywood all hold up in a bathroom when the finish is sealed and the top overhangs enough to shed water. Particleboard is the material that swells when it gets wet; check the cabinet box material on the spec sheet, not only the door. Homes & Gardens reports designers favoring wood vanities as a warm counterpoint to all the hard surfaces in a bathroom, with a stone or quartz top to protect the wood from water, which is a good rule whatever the color.

Color is the easy part, and the vanity is the best place in a bathroom to use it. A deep green, a navy, a warm walnut or a soft clay holds up because it sits low in the room and is balanced by white tile and a pale floor, as it is here.

Finally, measure the plumbing. Confirm the drain height and the supply lines will fit inside the new cabinet and not collide with a drawer.

Done looks like a vanity chosen at comfort height, with its depth checked against the clearances and its drawers clear of the plumbing.

Key Takeaway: Choose a vanity around 34 to 36 in tall, about 21 in deep or 18 in in tight rooms, built from plywood or solid wood, with drawers that clear the plumbing.

Editor Pick
HOMOTEK 6 Pack 3 Inch Hole Centers Brass Bronze Drawer Bin Cup Pulls Dresser Pulls for Cabinets,Furniture Handles,Kitchen Cabinet Hardware
HOMOTEK 6 Pack 3 Inch Hole Centers Brass Bronze Drawer Bin Cup Pulls Dresser Pulls for Cabinets,Furniture Handles,Kitchen Cabinet Hardware
Check price

Size a Single or Double Vanity to the Wall

Chart: One Sink or Two? Count the Wall. About 15 in (38 cm) from each sink center to the end, 30 in (76 cm) between centers.Save

The nineties primary bathroom made the double vanity standard, and for many couples it is the feature worth keeping most. The trap is fitting two sinks into a wall that only really holds one, which leaves two people elbow to elbow with no counter at all. The chart above sets out which vanity widths suit one sink and which suit two.

Work from the sink centers. Each sink wants about 15 in (38 cm) from its center to a side wall or the end of the counter, and two sinks want about 30 in (76 cm) or more between their centers, so two people can stand at them at once. Add those up and a double vanity needs at least 60 in (152 cm) to work at all. At 60 in, the two sinks sit close and the counter between them is narrow; it suits a household where people rarely use the sinks at the same moment. At 72 in (183 cm), there is room for a real stretch of counter between the bowls, which is where the double vanity starts to feel generous.

Below 60 in, choose a single sink. A 48 in (122 cm) vanity with one centered or offset sink gives far more usable counter than two sinks crammed into the same width. An offset sink, pushed to one side, leaves one long run of counter for a tray of everyday things.

Then the details of the double. Give each person their own mirror or a single wide mirror, with the lighting centered on each sink rather than the vanity as a whole; one fixture centered on a 72 in vanity leaves both faces lit from the side. Consider a central tower or a bank of drawers between the sinks, which gives each person storage without stealing counter. Keep the faucets the same model and finish, so the pair reads as one piece.

The transitional bathroom here gets the double right: a taupe-gray Shaker cabinet with brushed brass bar pulls, a white quartz top, and enough width that the counter between the sinks is real working space.

Check one more time that the full vanity width leaves the clearance in front of the toilet and the shower you marked at the layout stage.

Done looks like a vanity width chosen by counting sink centers and side clearances, with lighting and mirrors planned around each sink.

Key Takeaway: Plan a double vanity only at 60 in or more, better 72 in, with sink centers about 30 in apart and 15 in from each end; below 60 in, one sink serves better.

Editor Pick
Ravinte Brushed Brass Solid Pulls Cabinet Handles 5 Inch 10 Pack | Solid Zinc, Slim Design, Mounting Screws Included, Kitchen Cabinet Hardware, For Cupboards, Dressers, Drawers
Ravinte Brushed Brass Solid Pulls Cabinet Handles 5 Inch 10 Pack | Solid Zinc, Slim Design, Mounting Screws Included, Kitchen Cabinet Hardware, For Cupboards, Dressers, Drawers
Check price

Replace the Polished Brass With a Finish That Lasts

Bright European-style bathroom renovation; deep arched shower alcove tiled floor to ceiling in vertical dark forest-greeSave

Polished brass is the finish most people picture when they think of a nineties bathroom, and there is a reason it aged so visibly. Most of it relied on a clear lacquer coat to keep the metal from tarnishing. Over the years that coat gets scratched or broken by cleaning, and the brass underneath darkens in patches and the lacquer peels. Some faucets that looked like solid brass were really a brass-toned coating over nickel plating, and once that coating wears through, the color is simply gone. Metal finishers are candid that replating one faucet can cost more than buying a new one. So in most remodels the old brass goes.

Brass itself is not the problem; the dated version is shiny, lacquered and paired with cream and almond. The current version is satin or brushed, warmer, and used with intent, as in this bathroom: a wall-mounted two-handle faucet, a ceiling rain head, an oval mirror frame and a flush plate, all in one aged brass tone against forest green tile, walnut and white marble. The latest trend reports point to unlacquered brass in particular, which has no coating at all and develops a patina wherever hands touch it. That patina is the point; if you want the brass to stay bright, choose a PVD finish instead.

PVD, physical vapor deposition, bonds the finish to the metal itself rather than relying on a clear coat on top. It resists scratching and tarnish far better than the lacquers of the nineties, and several manufacturers back their PVD finishes with long warranties. For faucets you touch every day, it is the practical choice in any color: brass, nickel, black or bronze.

Order matters here more than people expect. A wall-mounted faucet, like the one over the vessel sink in this bathroom, needs its valve set in the wall before the wall is closed and tiled, so if you want one, the decision moves back to the rough-in stage. Check the spout reach as well: it should send water to about the center of the bowl, which for a vessel sink usually means a spout around 8 in (20 cm) long, and the spout should sit a few inches above the rim. A deck-mounted faucet can be chosen later, but confirm whether your new top is drilled for a single hole or a widespread set before you order.

Choose one metal for everything you touch: faucets, shower trim, towel bars and flush lever.

Done looks like every faucet and trim piece chosen in one finish family, the wall valves set if needed, and the old brass removed.

Key Takeaway: Replace peeling lacquered brass with a PVD finish for daily touch points, or unlacquered brass if you want patina, and set any wall-mounted valve before the walls close.

Editor Pick
Kingston Brass KS213SB Magellan 6" Adjustable Center Wall Mount Kitchen Faucet, Brushed Brass
Kingston Brass KS213SB Magellan 6" Adjustable Center Wall Mount Kitchen Faucet, Brushed Brass
Check price

Compare Finishes and Fixture Colors Before You Commit

Chart: Fixture Finishes Side by Side. One finish for everything you touch. A second, if any, for lights and frames.Save

With brass decided in principle, compare every finish side by side before anything is ordered, because a bathroom shows a mismatch more than any other room. The chart above sets the common choices against each other: how each one looks, how much care it asks, and what it sits well beside.

Polished chrome, like the wall-mounted faucet in this oak and sage bathroom, is the most durable and the easiest to clean, and it is the finish most likely to match an existing valve you are keeping. It shows water spots, but they wipe off. Brushed nickel hides spots and fingerprints better and has a slightly warmer cast; it was the finish that replaced brass in many bathrooms after the nineties, so it can look a little dated in its own way if paired with gray everything. Matte black reads graphic and current but shows hard-water marks and soap residue more than people expect, and its coating can wear on the edges of handles over time. Brushed or satin brass in PVD gives warmth with very little care. Unlacquered brass gives warmth and a living patina, with the expectation that it will darken and spot. Oil-rubbed bronze suits traditional rooms and hides wear, though it shifts in tone over the years.

The rule for mixing is simple: one finish for everything you touch with your hands, faucets, shower trim, towel bars, door handles, and if you want a second, use it for things you only look at, like light fixtures or a mirror frame. Two metals reads as deliberate. Three starts to read as accidental.

Fixture color deserves the same thought. Nineties bathrooms often came with almond or bone toilets, sinks and tubs, and colored porcelain does not take paint or reglazing as well as people hope on surfaces that see daily wear. If the almond toilet is staying for now, choose a warm white, cream or putty for the walls and tile so it reads as part of the scheme rather than a leftover; bright white beside almond makes the almond look dingy. When fixtures are replaced, replace them all in the same white at once. Mixing a new bright white toilet with an old almond tub is the most common way a refreshed bathroom gives away that it was refreshed in stages.

Put actual samples together under the bathroom’s own light: a faucet finish sample, a tile, the paint chip, the vanity door. Look at them in the morning and at night before choosing.

Done looks like one touch-finish chosen, an optional second for lighting, and a fixture color plan that either matches the almond or replaces it all at once.

Key Takeaway: Use one finish for everything you touch and at most a second for lights and frames, and either warm the palette around almond fixtures or replace them all together.

Editor Pick
GMISUN Amber Glass Soap Dispenser, 2 Pack Bathroom Hand Soap Dispensers with Stainless Steel Pump, 17 Fl Oz Kitchen Hand and Dish Soap Dispenser Set, Modern Vintage Liquid Brown Soap Dispensers Bottle
GMISUN Amber Glass Soap Dispenser, 2 Pack Bathroom Hand Soap Dispensers with Stainless Steel Pump, 17 Fl Oz Kitchen Hand and Dish Soap Dispenser Set, Modern Vintage Liquid Brown Soap Dispensers Bottle
Check price

Swap the Bulb Strip for Light That Flatters a Face

Narrow galley bathroom viewed from the doorwaySave

The strip of bare round bulbs above the mirror is the single most dated light in a nineties bathroom, and replacing it changes how the room feels every morning. The problem with the old strip was never the brightness. It was the bare bulbs, which glare in the mirror, and the position, a single line of light above the face that throws shadows under the eyes and the chin.

There are two good replacements. The best light for a face comes from both sides, a pair of sconces flanking the mirror at about face height, which lights the face evenly from left and right and leaves almost no shadow. That usually means new electrical boxes on either side of the mirror, which an electrician adds while the walls are open, so decide this at the rough-in stage if you can. The second option is a single fixture above the mirror, like the triple frosted globe sconce in brushed brass over the arched mirror in this galley bathroom. Frosted or opal glass spreads the light and removes the glare, and a fixture around three quarters of the mirror’s width spreads it wide enough to reach the sides of the face.

Bulbs matter as much as the fixture. Choose LED bulbs or an integrated LED fixture at a color temperature of 2700 to 3000K, which reads warm without turning skin orange, and a color rendering index of 90 or higher, which shows skin tones and makeup accurately. A dimmer on the vanity light lets the same fixture serve a bright morning routine and a quiet evening bath. Every fixture in a bathroom should carry at least a damp-location rating, and any fixture in or directly over the shower or tub needs the wet rating the manufacturer specifies.

Layer the rest of the room’s light so the vanity light does not do every job. A recessed light or a shower-rated downlight over the shower, a ceiling fixture or recessed lights for general light, and perhaps a small lamp-like glow from a niche or a night-light at the floor.

Mind the mirror. A sconce mounted where it overlaps a mirror frame looks crowded; keep a few inches of wall between each fixture and the frame.

This bathroom balances it well: a light oak vanity, white quartz, an arched brass mirror and a sage tile wall, all lit by one wide frosted fixture and the window at the end of the room.

Done looks like the bulb strip gone, sconces or a diffused bar wired to a correctly placed box on a dimmer, and bulbs chosen at 2700 to 3000K and 90 CRI or above.

Key Takeaway: Replace the bare bulb strip with side sconces or a wide frosted fixture, on a dimmer, using 2700 to 3000K bulbs with a CRI of 90 or higher.

Editor Pick
Modern Brushed Gold 3-Lights Vanity Light Fixtures with Milky White Glass Ball Shades, Mid Century Brass Wall Sconce Lighting Fixtures over Mirror, Wall Sconces for Bathroom Dressing Table Bedroom
Modern Brushed Gold 3-Lights Vanity Light Fixtures with Milky White Glass Ball Shades, Mid Century Brass Wall Sconce Lighting Fixtures over Mirror, Wall Sconces for Bathroom Dressing Table Bedroom
Check price

Hang Vanity Lights at the Heights That Work

Chart: Vanity Light Heights That Work. Mark every fixture center on the wall in pencil before the boxes go in.Save

Most vanity lighting goes wrong by a few inches, and the fix is a short set of numbers, gathered in the chart above. Mark them on the wall in pencil before the electrician sets a single box.

For side sconces, the center of each fixture goes about 60 to 66 in (152 to 168 cm) above the finished floor, which puts the light near the face of most adults; the NKBA’s grooming guidance centers around 60 in. The two sconces should sit roughly 36 to 40 in (91 to 102 cm) apart, center to center, close enough to light the face from both sides. That spacing usually means the mirror between them is around 24 to 30 in (61 to 76 cm) wide.

For a single fixture above the mirror, the center usually goes about 75 to 80 in (191 to 203 cm) above the floor, with the bottom of the fixture 3 to 4 in (8 to 10 cm) above the top of the mirror frame. Choose a width around three quarters of the mirror’s width, and never wider than the vanity. A bar the full width of a long mirror, like the eight-globe strip in this nineties bathroom, looks like a dressing room rather than a home.

For a double vanity, light each sink rather than the whole vanity. Either a pair of sconces at each mirror, or one fixture centered over each sink, so both people get even light.

Over the tub, the code is specific: hanging fixtures such as pendants and chandeliers are not allowed within a zone 3 ft (91 cm) out from the tub rim and 8 ft (2.4 m) up from it, so a decorative pendant over a freestanding tub needs a high ceiling or has to move. Recessed or close-mounted fixtures rated for damp or wet locations are the usual answer there.

Then the bulbs, again: 2700 to 3000K for a warm, natural tone and a CRI of 90 or above.

The bathroom in this section holds a whole nineties lighting lesson in one view: a long light oak vanity, a pink tile countertop, a full-width mirror, a rose border at the ceiling, and a strip of eight bare globes lighting all of it from one line above. Every number in the chart is a correction to that single strip.

Done looks like pencil marks on the wall for every fixture center, checked against the mirror size you plan to hang, before the boxes go in.

Key Takeaway: Center sconces 60 to 66 in high and 36 to 40 in apart, or a bar 75 to 80 in high and 3 to 4 in above the mirror, and keep pendants out of the zone over the tub.

Editor Pick
DUMOS Laundry Basket with Lid, 90L Wicker Laundry Hampers, Goose Yellow | 23.8 Gallon Woven Clothes Hamper with Side Handles, Removable Liner, Foldable Rattan Laundry Basket with Sturdy Steel Frame
DUMOS Laundry Basket with Lid, 90L Wicker Laundry Hampers, Goose Yellow | 23.8 Gallon Woven Clothes Hamper with Side Handles, Removable Liner, Foldable Rattan Laundry Basket with Sturdy Steel Frame
Check price

Paint the Walls Last and Choose One Color Story

Narrow Edwardian-revival bathroom viewed straight-onSave

Paint comes last for a practical reason: every trade before it, the plumber, the electrician, the tile setter and the vanity installer, scuffs the walls. Paint after them and you paint once. It also comes last because it is the cheapest decision to change and the one that should respond to everything already in the room, the tile, the vanity, the metal and the light.

Choose one color story and let everything answer to it. This bathroom shows how strong a single story can be: deep teal-navy walls above white subway tile wainscoting, a dark olive border at chair-rail height, a black and white diamond mosaic floor, oil-rubbed bronze sconces with amber globes. One deep color above, crisp white below, a dark accent line between them, and nothing fighting. A nineties bathroom often suffered from the opposite, sage walls against a pink counter beside a seafoam tub, each a reasonable color alone and a muddle together.

Small bathrooms can take deep color well, which surprises people. A dark wall above a white tile wainscot makes a small room feel enclosed and finished rather than cramped, especially with a white ceiling and a light floor. If you are nervous, paint a large sample board and tape it to the wall for a few days, looking at it morning and night.

Prepare properly. Walls that held wallpaper need that adhesive washed off and a primer made for wallpaper glue before any color goes on. Patched drywall needs a primer over the patches so they do not flash through the paint. Then choose a finish made for bathrooms: a satin or semi-gloss resists moisture and wipes clean, and many paint lines offer a bathroom formula with mildew resistance built in. Ceilings in bathrooms get the same moisture as walls, so use a moisture-resistant ceiling paint rather than a flat one.

Paint the trim and the door at the same time, in a color chosen with the walls, often a white that matches the tile.

As for names: the color in your sample should be judged with your eyes in your room. Bring home real chips from the brand you plan to buy, compare them against the tile and the vanity, and choose by what you see.

Done looks like walls primed and painted in a moisture-resistant satin or semi-gloss, the ceiling done in a bathroom-rated paint, and one color story carried from floor to ceiling.

Key Takeaway: Paint after every other trade is done, pick one color story that answers to the tile and the vanity, and use a primed, moisture-resistant satin or semi-gloss.

Editor Pick
RONGHUAFUGUI Antique Gothic Amber Glass Wall Sconce for Bedroom, 2-Pack | Rustic Black Brushed Gold Farmhouse Wall Light Fixture, Vintage Decorative Metal Wall Lamp for Hallway, Living Room, Entryway
RONGHUAFUGUI Antique Gothic Amber Glass Wall Sconce for Bedroom, 2-Pack | Rustic Black Brushed Gold Farmhouse Wall Light Fixture, Vintage Decorative Metal Wall Lamp for Hallway, Living Room, Entryway
Check price

Walk the Finished Room With a Final Punch List

Chart: The Final Punch List. Test everything that moves, runs, drains or switches, while the trades are easy to call back.Save

The last stage is the one most often skipped, and it is the one that catches the small problems while the people who caused them are still easy to call back. Walk the finished room slowly with the checklist in the chart above, and test everything that moves, runs, drains or switches.

Start with water. Run every faucet hot and cold, fill the tub and drain it, and run the shower for several minutes. Then look under the vanity with a flashlight for drips at the supply lines and the drain, and check again the next day, because slow leaks show up later. Check that the shower valve’s maximum temperature is set so the water cannot scald; most current valves have an adjustable limit stop. Flush the toilet several times and make sure it does not rock on the floor.

Then the seals. Every change of plane in the shower, every joint where the tub meets tile and the vanity top meets the wall, should be caulked with a flexible sealant, not grouted. Look for gaps and skips. Close the shower glass and check that the sweep or seal meets the curb. Confirm the grout has been sealed if it needed sealing.

Then power and air. Press the test and reset buttons on every GFCI outlet. Switch on every light and dimmer at its full range. Run the exhaust fan and hold a square of tissue paper at the grille; it should pull firmly toward the fan. If you can, go outside and check air is leaving at the cap.

Then the finishes. Open and close every door and drawer, check the hardware is tight, look along the paint at a low angle with a flashlight for skipped spots and drips, and confirm the mirror is level and secured.

Finally, the paperwork. Keep a labeled leftover of each paint, a spare box of tile, the grout color name, and the manuals and warranties for the fan, the faucets and the valve in one folder. A bathroom built in the nineties went thirty years without anyone knowing what was behind its walls. Yours should not.

This sloped-ceiling bathroom, with its white double vanity and granite top, shows how much of a light remodel depends on details like these.

Done looks like every item checked off, every problem written down and fixed, and a folder of leftovers and manuals on a shelf.

Key Takeaway: Test every faucet, drain, seal, outlet, light and the fan before you call it finished, then keep leftover materials and manuals together for the next owner.

Editor Pick
Klein Tools RT250 GFCI Outlet Tester with LCD Display, Electric Voltage Tester for Standard 3-Wire 120V Electrical Receptacles
Klein Tools RT250 GFCI Outlet Tester with LCD Display, Electric Voltage Tester for Standard 3-Wire 120V Electrical Receptacles
Check price

A 1990s bathroom remodel turns into a manageable project the moment it becomes a sequence. Name every feature, sort it, and look behind the surfaces before anything is chosen, so the hidden water damage and the attic-venting fan are fixed before they can ruin new work. Settle the big pieces next, the garden tub, the shower and the layout, while the walls are open. Then work outward in order: floor, top, vanity, finishes, light and, last of all, paint.

The garden tub, the cultured marble and the honey oak each deserve an honest call instead of an automatic demolition. Some stay. The polished brass, the bare bulb strip and the glued mirror almost always go.

Start this week with the first stage: a notepad, a tape measure, a flashlight and an hour in the room. Write the list, mark the drains, and the rest of the plan will follow from what you find.

You've saved it, wanted it. Here's the how: codes, measurements, order. Your choices make it yours.

See all guides →

Every original feature gets its call before a single tile comes off, so each step protects the last. A Nineties Bathroom Remodel, Stage by Stage, Toward a Room That Feels Calm. See the full plan.Save
Georgia

Georgia

I'm Georgia, an interior writer covering interior design and home decor across its full range — color and texture, layout and lighting, small-space fixes and seasonal styling. One standard runs through all of it: every idea has to hold up in a real home, not just a photograph.